• Pico-Sensor-Kit-B
• The pico sensor kit, with IR remote controller, PH2.0 dual-plug 4PIN cable, and PH2.0 4PIN cable.

• Raspberry-Pi-Pico-Sensor-Kit-B
• On the basis of the Pico-Sensor-Kit-B, it is equipped with Raspberry Pi Pico H and Type A to Micro B USB cable. The Raspberry Pi Pico H is a low-cost, high-performance microcontroller board with flexible digital interfaces. Comes with online development resources and tutorials to help you get started easily.

• Raspberry-Pi-Pico-W-Sensor-Kit-B
• On the basis of the Pico-Sensor-Kit-B, it is equipped with Raspberry-Pi-Pico-W-M and Type A to Micro B USB cable. Based on Raspberry Pi Pico, Raspberry Pi Pico W comes with a wireless communication module which supports Wi-Fi 4 wireless networks, making it the perfect solution for wireless network control and communication.

• RP2040-Plus-Pico-Sensor-Kit-B
• On the basis of the Pico-Sensor-Kit-B, it is equipped with RP2040-Plus-M and Type A to Type C USB cable. The RP2040-Plus is based on Pico with onboard 4MB Flash, Type C connector, recharge header, and higher current DC-DC chip, which can meet more application requirements.

•  Pico-Sensor-Expender
• Onboard PH2.0 header for 3.7V Lithium battery, allows recharging the battery and powering the board at the same time.
• Onboard PH2.0 4PIN headers for connecting modules
• 1. 1.5inch OLED Module
• Built in controller: SSD1327
• Resolution: 128×128
• 16 gray scale display
• I2C and SPI communication, switchable via onboard BS1 and BS2 resistors
• 2. 6-Axis Attitude Sensor
• Onboard QMI8658C (3-axis accelerometer, 3-axis gyroscope), for detecting motion and orientation
• 16-bit resolution for both accelerometer and gyroscope
• 3. VOC Sensor
• Onboard SGP40 digital VOC gas sensor for air quality detection
• Measurement range: 0~1000ppm ethanol equivalents
• Communication interface: I2C (constant address: 0x59)
• Operating voltage: 3.3V/5V
• 4. Potentiometer Module
• Adjustable voltage output, after the output voltage exceeds the LED conduction voltage, the LED brightness will increase with voltage
• 5. Photoresistor Module
• For detecting the ambient light brightness, the output voltage will decrease as the brightness increases
• 6. Sound Sensor Module
• For converting the sound signal into electrical signal, which is amplified through operational amplifier and then inputted to the comparator, providing analog voltage output and digital output respectively. Adjustable output amplitude via potentiometer A and digital interface trigger voltage via potentiometer D.
• 7. RGB LED Module
• Built in controller: WS2812B
• Brightness: 256 levels adjustable
• Color depth: 24 bits (R / G / B 8-bit each color, can be combined to 16777216 colors)
• 8. Buzzer Module
• Onboard passive buzzer, outputs different sounds according to the different frequencies of the electrical signal.
• 9. IR Receiver Module
• Onboard IRM-H638T/TR2 for receiving infrared remote control signal
• 10. IR Transmitter Module
• Onboard TSAL6400 for transmitting infrared remote control signals, with the infrared light wavelength of 940nm.
• 11. Button Module
• Onboard 12×12mm button, for human-computer interaction
• 12. LED Module
• Onboard 10mm LED with soft light, for status indication
• 13.Temperature/Humidity Module
• Onboard SHTC3 chip supports measuring 0 to 100% relative humidity and -40°C to 125°C temperature, with a typical measurement accuracy of ±2% relative humidity and ±0.2°C
• 14. EEPROM Module
• Onboard AT24C04 chip for preserving 2Kbit of data when powered down
• 15. Motor Driver Module
• Onboard PCA9685 chip, can output 12-bit hardware PWM to control motor speed
• Onboard TB6612FNG dual H-bridge motor driver chip, high efficiency, not easy to heat
• logic voltage: 3.3V

Documentation:

• Product Wiki

Package Includes:

• Sensor Kit only
• 1 x Pico-Sensor-Kit-B
• 1 x IR remote controller 
• 15 x PH2.0 dual-plug 4PIN cable

• 5 x PH2.0 4PIN cable 
• Raspberry Pi Pico H + Sensor Kit
• 1 x Pico-Sensor-Kit-B 
• 1 x Raspberry Pi Pico H 
• 1 x IR remote controller 
• 15 x PH2.0 dual-plug 4PIN cable
• 5 x PH2.0 4PIN cable
• 2 x Type A to Micro B USB cable ~1.2m
• Raspberry-Pi-Pico-W-M + Sensor Kit
• 1 x Pico-Sensor-Kit-B 
• 1 x Raspberry-Pi-Pico-W-M 
• 1 x IR remote controller 
• 15 x PH2.0 dual-plug 4PIN cable 
• 5 x PH2.0 4PIN cable 
• 1 x Type A to Micro B USB cable ~1.2m 
• RP2040-Plus-M + Sensor Kit
• 1 x Pico-Sensor-Kit-B 
• 1 x RP2040-Plus-M 
• 1 x IR remote controller 
• 15 x PH2.0 dual-plug 4PIN cable 
• 5 x PH2.0 4PIN cable 
• 1 x Type A to Type C USB cable ~1m