Out of the box, the bladeRF can tune from 300MHz to 3.8GHz without the need for extra boards. Through open source software such as GNURadio (live image), the bladeRF can be placed into immediate use. With its flexible hardware and software, the bladeRF can be configured to operate as a custom RF modem, a GSM and LTE picocell, a GPS receiver, an ATSC transmitter, or a combination Bluetooth/WiFi client, without the need for any expansion cards. All of the bladeRF host software, firmware, and HDL is open source, and available on GitHub.
USB 3.0 Superspeed
High speed, low latency and increased power delivery over a single cable: USB 3.0 Superspeed is the perfect interface for a wide bandwidth radio front end to modern computers. The Cypress FX3 microcontroller is the ideal solution with a powerful ARM9 processor and enough bandwidth to saturate the full duplex 5Gbps USB 3.0 link.
Fully Programmable FPGA
An Altera Cyclone IV FPGA provides the interface between the FX3 and RF transceiver. This FPGA has single-cycle access embedded memory, hard 18x18 multipliers for dedicated DSP and many general logic elements ready to be programmed.
Wideband RF Transceiver
From bits to RF, the LimeMicro LMS6002D is a fully integrated RF transceiver. Made to power picocell stations, this transceiver is capable of handling anything from simple FM audio to the latest 4G LTE standard to whatever the future may hold.
Professional Quality
Highlights:
- Full-duplex 40MSPS 12bit quadrature sampling
- Factory calibrated VCTCXO tuned within 1 Hz of 38.4 MHz
- Removable-cap RF shields for increased system sensitivity and isolation
- Flexible clocking architecture for arbitrary sample rates
- GPIO expansion port ( GPIO Expansion Board )
- SPI flash allows for headless operation
- Expanded frequency coverage using XB-200 Transverter Board
- Typical +6dBm TX power
Technical Specifications:
- Fully bus-powered USB 3.0 SuperSpeed Software Defined Radio
- Portable, handheld form factor: 5" by 3.5"
- Gold plated RF SMA connectors
- 300MHz - 3.8GHz RF frequency range
- Independent RX/TX 12-bit 40MSPS quadrature sampling
- Flexible clocking architecture
- Capable of achieving full-duplex 28MHz channels
- 16-bit DAC factory calibrated 38.4MHz +/-1ppm VCTCXO
- On-board 200MHz ARM9 with 512KB embedded SRAM (JTAG port available)
- On-board 40KLE Altera Cyclone 4 E FPGA (JTAG port available)
- 2x2 MIMO configurable with SMB cable, expandable up to 4x4
- Modular expansion board design for adding GPIO and expanding frequency range,
- DC power jack for running headless
- Highly efficient, low noise power architecture
- Stable Linux, Windows, Mac and GNURadio software support
High speed, low latency and increased power delivery over a single cable: USB 3.0 Superspeed is the perfect interface for a wide bandwidth radio front end to modern computers. The Cypress FX3 microcontroller is the ideal solution with a powerful ARM9 processor and enough bandwidth to saturate the full duplex 5Gbps USB 3.0 link.
An Altera Cyclone IV FPGA provides the interface between the FX3 and RF transceiver. This FPGA has single-cycle access embedded memory, hard 18x18 multipliers for dedicated DSP and many general logic elements ready to be programmed.
From bits to RF, the LimeMicro LMS6002D is a fully integrated RF transceiver. Made to power picocell stations, this transceiver is capable of handling anything from simple FM audio to the latest 4G LTE standard to whatever the future may hold.
Professional Quality
The bladeRF's design has been tested and verify to meet our very high standards. At peak RF performance, the bladeRF can occupy 28MHz of bandwidth over its operating bandwidth without any significant spurs.
Documents:
Package Includes:
- bladeRF x40 (40KLE Cyclone 4 FPGA)
- USB 3.0 SS cable
- 2x SMA cables
SDR Specifications | |
Tuning range | 300MHz to 3.8GHz |
Duplex | Full-duplex |
Max sampling rate | 40MSPS |
ADC/DAC resolution | 12bit quadrature sampling |
Max RF bandwidth | 28MHz |
bladeRF X40
- Brand: Nuand
- Product Code:Nuand-bladeRF-x40
- Reward Points:660
- Availability:In Stock
-
रo 66,033.00
- Price in reward points:66033
-
- 2 or more रo 65,496.00
Related Products
Tags: Bladerf x40 USB 3.0 GNU Radio 300MHz to 3.8GHz GPIO 1 Hz of 38.4 MHzRF 40MSPS 12bit quadrature sampling Windows Linux Mac