The Tic T834 USB Multi-Interface Stepper Motor Controller makes basic control of a stepper motor easy, with quick configuration over USB using our free software. The controller supports six control interfaces: USB, TTL serial, I²C, analog voltage (potentiometer), quadrature encoder, and hobby radio control (RC). This version incorporates a TI DRV8834 driver and ships with soldered header pins and terminal blocks. It can operate from 2.5 V to 10.8 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (or 2 A max with sufficient additional cooling).

The Tic family of stepper motor controllers makes it easy to add basic control of a bipolar stepper motor to a variety of projects. These versatile, general-purpose modules support six different control interfaces: USB for direct connection to a computer, TTL serial and I²C for use with a microcontroller, RC hobby servo pulses for use in an RC system, analog voltages for use with a potentiometer or analog joystick, and quadrature encoder for use with a rotary encoder dial. They also offer many settings that can be configured using our free configuration utility (for Windows, Linux, and macOS). This software simplifies initial setup of the device and allows for in-system testing and monitoring of the controller via USB (a micro-B USB cable is required to connect the Tic to a computer).
 
The table below lists the members of the Tic family and shows the key differences among them.

                                                         

Tic T500      


Tic T834

Tic T825

Tic T249

Operating voltage range: 4.5 V to 35 V(1) 2.5 V to 10.8 V 8.5 V to 45 V(1) 10 V to 47 V(1)
Max continuous current per phase
(no additional cooling):
1.5 A 1.5 A 1.5 A 1.8 A
Peak current per phase
(additional cooling required):
2.5 A 2 A 2.5 A 4.5 A
Microstep resolutions: full
half
1/4
1/8
full
half
1/4
1/8
1/16
1/32
full
half
1/4
1/8
1/16
1/32
full
half
1/4
1/8
1/16
1/32
Automatic decay selection: Yes     Yes
Automatic gain control (AGC):       Yes
Driver IC: MP6500 DRV8834 DRV8825 TB67S249FTG
Price (connectors not soldered): $19.95 $29.95 $29.95 $39.95
Price (connectors soldered): $21.95 $31.95 $31.95 $41.95

Tic T825 USB Multi-Interface Stepper Motor Controller, bottom view with dimensions.

Tic T834 USB Multi-Interface Stepper Motor Controller, bottom view with dimensions.

Tic T500 USB Multi-Interface Stepper Motor Controller, bottom view with dimensions.

Features and specifications

  • Open-loop speed or position control of one bipolar stepper motor
  • A variety of control interfaces:
    • USB for direct connection to a computer
    • TTL serial operating at 5 V for use with a microcontroller
    • I²C for use with a microcontroller
    • RC hobby servo pulsesfor use in an RC system
    • Analog voltage for use with a potentiometer or analog joystick
    • Quadrature encoder input for use with a rotary encoder dial, allowing full rotation without limits (notfor position feedback)
    • STEP/DIR inputs for compatibility with existing stepper motor control firmware
  • Acceleration and deceleration limiting
  • Maximum stepper speed: 50,000 steps per second
  • Very slow speeds down to 1 step every 200 seconds (or 1 step every 1428 seconds with reduced resolution).
  • Up to six different microstep resolutions:
    • The Tic T825 and Tic T834 supports full step, half step, 1/4 step, 1/8 step, 1/16 step, and 1/32 step
    • The Tic T500 supports full step, half step, 1/4 step, 1/8 step
  • Digitally adjustable current limit
  • Optional safety controls to avoid unexpectedly powering the motor
  • Input calibration (learning) and adjustable scaling degree for analog and RC signals
  • 5 V regulator (no external logic voltage supply needed)
  • Optional kill switch inputs
  • STEP/DIR outputs for controlling external stepper motor drivers
  • Connects to a computer through USB via a USB A to Micro-B cable(not included)
  • Free configuration software available for Windows, Linux, and macOS
  • Comprehensive user’s guide

 

The Tic T834 is based on the DRV8834 IC from Texas Instruments. It can operate from 2.5 V to 10.8 V and can deliver up to approximately 1.5 A continuous per phase without a heat sink or forced air flow (the peak current per phase is 2 A). This version is sold with connectors soldered so no soldering is necessary to use it.
 
Tic T834 USB Multi-Interface Stepper Motor Controller (Connectors Soldered).
 
 
 
 
                                                                                   Tic T834 USB Multi-Interface Stepper Motor
                                                                         Controller (Connectors Soldered).
Specs:here
 
Resources:here
 
Faqs:here
 
Package Contains:
  • 1 x Tic T834  USB Multi-Interface Stepper Motor Controller
  • 1 x  Included headers and terminal blocks
 
 

Write a review

Please login or register to review

Pololu 3132 / 3133 Tic T834 USB Multi-Interface Stepper Motor Controller

  • Brand: Pololu
  • Product Code:Pololu-3132-33-Stepper-Motor-Controller
  • Reward Points:64
  • Availability:In Stock
  • रo 6,398.00

  • Price in reward points:6398

  • 2 or more रo 6,347.00
  • 4 or more रo 6,296.00
  • 10 or more रo 6,245.00
  • 20 or more रo 6,194.00

Available Options


Related Products

Pololu 3130 / 3131 Tic T825 USB Multi-Interface Stepper Motor Controller

Pololu 3130 / 3131 Tic T825 USB Multi-Interface Stepper Motor Controller

The Tic T825 USB Multi-Interface Stepper Motor Controller makes basic control of a stepper motor eas..

रo 6,612.00

Pololu 3134/3135 Tic T500 USB Multi-Interface Stepper Motor Controller

Pololu 3134/3135 Tic T500 USB Multi-Interface Stepper Motor Controller

The Tic family of stepper motor controllers makes it easy to add basic control of a bipolar stepper ..

रo 2,242.00 रo 2,547.00

Pololu 3138 / 3139 Tic T249 USB Multi-Interface Stepper Motor Controller

Pololu 3138 / 3139 Tic T249 USB Multi-Interface Stepper Motor Controller

The Tic T249 USB Multi-Interface Stepper Motor Controller makes basic control of a stepper motor eas..

रo 3,738.00 रo 4,248.00

Tags: Tic, T834, USB, Multi-Interface, Stepper, Motor, Controller

The product is currently Out-of-Stock. Enter your email address below and we will notify you as soon as the product is available.

Name
Email
Phone
Comments