The GP2Y0A60SZ distance sensor from Sharp offers a wide detection range of 4″ to 60″ (10 cm to 150 cm) and a high update rate of 60 Hz. The distance is indicated by an analog voltage, so only a single analog input is required to interface with the module. The sensor ships installed on our compact carrier board, which makes it easy to integrate this great sensor into your project, and is configured for 5V mode.
 

                                                           

Sharp’s distance sensors are a popular choice for many projects that require accurate distance measurements. This particular sensor is small and affordable, making it an attractive alternative to sonar rangefinders, while its wide sensing range and resistance to interference from ambient IR set it apart from other IR distance sensors. It consists of a Sharp GP2Y0A60SZLF module installed on our compact carrier board, which includes all of the external components required to make it work and provides a 0.1″ pin spacing that is compatible with standard connectors, solderless breadboards, and perfboards. With an ability to measure distances from as close as four inches to as far as five feet (10 cm to 150 cm), this sensor has the widest range of any of our Sharp distance sensors, and its 60 Hz update rate is more than twice that of Sharp’s older  that has a GP2Y0A02YK0F analog distance sensor similar sensing range.

                                       

Interfacing to most microcontrollers is straightforward: the single analog output, OUT, can be connected to an analog-to-digital converter for taking distance measurements, or the output can be connected to a comparator for threshold detection. The sensor automatically updates the output approximately every 16 ms. The enable pin, EN, can be driven low to disable the IR emitter and put the sensor into a low-current stand-by mode. This pin is pulled high on the carrier board through a 10 kΩ pull-up resistor to enable the sensor by default.

A 1×4 strip of 0.1″ header pins and a 1×4 strip of 0.1″ right-angle header pins are included, as shown in the picture below. You can solder the header strip of your choice to the board for use with custom cables or solderless breadboards, or you can solder wires directly to the board itself for more compact installations. The board features one 0.125″ mounting hole that works with #4 or M3 screws (not included); if you do not need the mounting hole, you can cut that part of the board off to reduce its size.

                                                      

5V and 3V versions

The GP2Y0A60SZ supports two operating modes: 5V and 3V. In 5V mode, the recommended operating voltage is 2.7 V to 5.5 V, and the output voltage differential over the full distance range is approximately 3 V, varying from around 3.6 V at 10 cm to 0.6 V at 150 cm. In 3V mode, the recommended operating voltage is 2.7 V to 3.6 V, and the output voltage differential over the full distance range is approximately 1.6 V, varying from around 1.9 V at 10 cm to 0.3 V at 150 cm. The GP2Y0A60SZ datasheet (701k pdf) contains a plot of analog output voltage as a function of the distance for the two modes.

Our GP2Y0A60 carrier board is available configured for 5V mode or configured for 3V mode:

                                                 
 
The only difference between the two versions is the presence or absence of a zero ohm resistor as shown in the picture above (the component location is marked by a rectangle on the silkscreen). You can convert a 5V version to 3V by removing the resistor, and you can convert a 3V version to 5V by shorting across the two pads.
 
Note that the 5V version can be powered all the way down to 2.7 V, and the relationship between the sensor output voltage and distance is mostly independent of the supply voltage. The main drawback to powering the 5V version at a lower voltage is the output voltage will not exceed the supply voltage, so the effective minimum detection distance might increase (i.e. for distances that would result in output voltages above your supply voltage, the output will instead be capped at the supply voltage). On the other hand, if you mostly care about measuring distances closer to the maximum end of the range, you could benefit from the increased output voltage differential of the 5V version even if you are only powering it at 3.3 V.
 
 

Feature summary

  • Operating voltage:
    • 5V version: 2.7 V to 5.5 V
    • 3V version: 2.7 V to 3.6 V
  • Average current consumption: 33 mA (typical)
  • Distance measuring range: 10 cm to 150 cm (4″ to 60″)
  • Output type: analog voltage
  • Output voltage differential over distance range:
    • 5V version: 3.0 V (typical)
    • 3V version: 1.6 V (typical)
  • Update period: 16.5 ± 4 ms
  • Enable pin can optionally be used to disable the emitter and save power
  • Size without header pins: 33 mm × 10.4 mm × 10.2 mm (1.3″ × 0.41″ × 0.4″)
  • Weight without header pins: 2.5 g (0.09 oz)

Schematic diagram

       

         

Package Contents :

  • 1 x GP2Y0A60SZLF
  • 1 x Straight Header pins
  • 1 x 90 degrees Header pins

Useful Links :

downloadable pdf 

Electrical Specifications
Input Current Supply Current - 33mA
Minimum Operating Voltage 2.7V
Maximum Operating Voltage 5.5V
Physical Attributes
Weight 2.5 g
Dimensions 1.3″ × 0.41″ × 0.4″

Write a review

Please login or register to review

Pololu 2474 Carrier with Sharp GP2Y0A60SZLF Analog Distance Sensor 10-150cm

  • Brand: Pololu
  • Product Code:Pololu-Analog-Sharp-Distance-Sensor-GP2Y0A60SZLF
  • Reward Points:18
  • Availability:In Stock
  • रo 1,763.00

  • Price in reward points:1763

  • 5 or more रo 1,738.00
  • 8 or more रo 1,724.00
  • 15 or more रo 1,710.00
  • 40 or more रo 1,696.00
  • 80 or more रo 1,682.00

Available Options


Related Products

IR Distance Sensor - Sharp GP2Y0A21YK0F

IR Distance Sensor - Sharp GP2Y0A21YK0F

IR Distance Sensor - Sharp GP2Y0A21YK0F with wire connector Features and Specifications: ..

रo 481.00

Pololu 2489/2490/3415/3416 Time-of-Flight Distance Sensor Carrier with Voltage Regulator VL53L0X/ VL53L1X/ VL6180X

Pololu 2489/2490/3415/3416 Time-of-Flight Distance Sensor Carrier with Voltage Regulator VL53L0X/ VL53L1X/ VL6180X

These sensors are a carrier/breakout board for ST’s VL6180X, VL53L0X or VL53L1X laser-ranging sensor..

रo 1,009.00 रo 1,147.00

Pololu 2464 Analog Distance Sensor -  4-30cm Sharp GP2Y0A41SK0F

Pololu 2464 Analog Distance Sensor - 4-30cm Sharp GP2Y0A41SK0F

The GP2Y0A41SK0F Sharp analog distance sensor features a detection range of 1.5″ to 12″ (4 cm to 30 ..

रo 1,174.00

Gravity: Digital Infrared Distance Sensor - 10cm

Gravity: Digital Infrared Distance Sensor - 10cm

This is an edge detection sensor from DFRobot. It will help your robot detect the edge of a precipic..

रo 813.00 रo 937.00

Pololu 3692 VL53L4CD Time-of-Flight Distance Sensor Carrier with Voltage Regulator, 120cm Max

Pololu 3692 VL53L4CD Time-of-Flight Distance Sensor Carrier with Voltage Regulator, 120cm Max

This sensor is a carrier/breakout board for ST’s VL53L4CD laser-ranging sensor, which offers fast (u..

रo 1,157.00

Tags: Pololu, Analog, Distance, Sensor

The product is currently Out-of-Stock. Enter your email address below and we will notify you as soon as the product is available.

Name
Email
Phone
Comments