Now shipping v1.3!  We believe this is the best SDR upconverter available. Here is why.
Major version changes:
  • Proudly designed, fabricated and assembled in the USA and Canada!
  • Input, output and LO filters reconfigured for substantial sensitivity and selectivity improvements
  • New ultra low-noise linear power regulator (LP5907), with voltage noise under 10 µVRMS!
  • Optional battery-powered operation for DXing on the go!  (easy-to-assemble AAA battery holder sold separately, or roll-your-own solution with the easily-accessible battery power input vias)
  • New side-mount LED indicators, easily visible with or without an enclosure (Green = upconvert mode enabled; Yellow = USB powered; Red = low voltage)
  • Fully-assembled broadband RF noise source built-in (Note: SMA output jack excluded to comply with government regulations, but can be purchased separately)
  • u.FL socket (also known as IPX and UMCC) available for optional clock injection from an external clock source, should a higher-accuracy clock be desired
  • 5 other u.FL socket mounting footprints for simplified testing, troubleshooting and demonstrational purposes
  • Additional mounting holes to facilitate custom installations
  • Sturdy right-angle SMA connectors to improve spacing tolerances and ensure physical compatibility with our machined aluminum enclosures (enclosures sold separately)
  • Redesigned for a surface-mount oscillator to eliminate potential oscillator-desocketing issues
IMPORTANT NOTE:  due to changes implemented in v1.3, enclosures built for previous Ham It Up models are NOT 100% compatible.  Specifically, new end-panels are required for full compatibility with older enclosures.  Along with v1.3-specific enclosures, we also carry end-panel sets to allow for installation of Ham It Up v1.3 into older enclosures.  If you cannot find these in our store, please contact us!
Standard features:
  • Female SMA for both input and output for a wide array of connectivity options 
  • In-line SMA connectors.  Much easier to connect and manipulate than side-by-side SMA connectors 
  • Antenna protection on RF input--in-circuit in both enable and passthrough mode--to protect your Ham It Up & SDR from stray ESD
  • All critical components sourced exclusively from North American parts distributors
  • Only ultra-low-noise components used in the signal path
  • Ultra-high-Q, low ESR inductors and capacitors used for all filters
  • Powered by a sturdy & common USB-B USB socket for a multitude of power input options 
  • RF-suitable power supply regulation (LP5907) 
  • PTC fuse on USB power input to protect your Ham It Up upconverter from short circuits
  • Upconverter enable/passthrough toggle switch--less fiddling with small, delicate cables and connectors 
  • 125MHz oscillator for improved sensitivity (away from high-traffic RF zones, like broadcast FM)
  • Stable <25ppm oscillator included 
  • LO disabled in passthrough mode 
  • A maximum input level of +1dBm with LO at +7dBm
  • High-quality 2-layer PCB with ENIG finish 
  • Small, light-weight PCB (just 3.8" x 1.9")
  • Designed to fit standard off-the-shelf Hammond enclosures 
  • 7 mounting holes for standard PC screws 
  • Designed and manufactured in conjunction with Opendous Inc., an excellent open-hardware design company 
  • Full project documentation--schematics, PCB design files, assembly information--is freely available.  
  • A portion of the proceeds from your purchase will be used to support this and other open-hardware, open-source initiatives
BONUS!  We had space left on the PCB, so rather than waste it we have added a noise source circuit at no additional cost! We have even populated most of the components for you. We have the SMA connector required to complete this bonus noise source circuit available for a small additional fee. Details of the noise source circuit are available with the project documentation.
Operation:
Before operating your unit for the first time, and every time you run with a new SDR, we recommend running the tuning procedure located here. It is not a mandatory procedure but may help fine-tune your, erm. tuning.  The basic operational instructions follow.
  • Connect your antenna to the RF input 
  • Connect your SDR to the IF output 
  • Ensure your toggle switch is in the enable position 
  • Plug your USB power source into the USB-B USB jack 
  • Fire up your favorite SDR software.  Tune to 125MHz + (+/- the tuning offset from the tuning procedure) + your desired frequency and enjoy!
Installation & Demo Video:

Package Includes:
  • 1 x Ham It Up v1.3 Barebones - HF Upconverter
 

Write a review

Please login or register to review

Ham It Up v1.3 Barebones - HF Upconverter

  • Brand: Nooelec
  • Product Code:NE-Ham-It-Up-v1.3
  • Reward Points:57
  • Availability:In Stock
  • रo 5,685.00

  • Price in reward points:5685

  • 3 or more रo 5,640.00
  • 5 or more रo 5,595.00
  • 13 or more रo 5,545.00
  • 25 or more रo 5,500.00

Related Products

SDR Receiver - RTL2832U+R820T2 - USB Stick version with Antenna and Remote

SDR Receiver - RTL2832U+R820T2 - USB Stick version with Antenna and Remote

Watch and record digital terrestrial TV on PC or Laptop Watch DVB-T digital TV and listen to DAB..

रo 1,445.00

SMA Male to MCX Male RG178 Cable Connector

SMA Male to MCX Male RG178 Cable Connector

SMA Male to MCX Male RG178 Cable Connector   Features: Frequency Range: 0-300..

रo 267.00

UFL/IPX to SMA Female RG178 Pigtail Cable Connector

UFL/IPX to SMA Female RG178 Pigtail Cable Connector

UFL/IPX to SMA Female RG178 Pigtail Cable Connector. Connects internal WiFi to external WiFi Booster..

रo 135.00

SDR Satellite TV Receiver RTL2832U and FC0012 USB DVB-T

SDR Satellite TV Receiver RTL2832U and FC0012 USB DVB-T

Satellite TV Receiver RTL2832U / FC0013 USB DVB-T supports Windows 7 Linux   EDAL RTL283..

रo 895.00

Extruded Aluminum Enclosure Kit for Ham It Up

Extruded Aluminum Enclosure Kit for Ham It Up

These high-quality aluminum enclosures (or aluminium, if you're weird like that) are custom-made for..

रo 2,270.00

SDR RTL2832 + R820T - DIY Kit

SDR RTL2832 + R820T - DIY Kit

Do-it-Yourself SDR to be soldered Kit ! The receiver take RTL2832U + R820T programs , taking adv..

रo 2,785.00 रo 3,000.00

SDR RTL2832 + R820T

SDR RTL2832 + R820T

SDR RTL2832 + R820T The receiver take RTL2832U + R820T programs , taking advantage of the Q chan..

रo 2,950.00

SDR XTR+ Tiny Extended-Range TCXO-Based SDR & DVB-T USB Stick (RTL2832U + E4000) with Antenna and Remote Control

SDR XTR+ Tiny Extended-Range TCXO-Based SDR & DVB-T USB Stick (RTL2832U + E4000) with Antenna and Remote Control

SDR XTR+ tiny SDR & DVB-T USB set, including GPS-rated +/- 0.5PPM TCXO, quality telescopic antenna a..

रo 4,545.00

NooElec NESDR XTR Tiny SDR and DVB-T USB Stick (RTL2832U + E4000) with Antenna and Remote Control

NooElec NESDR XTR Tiny SDR and DVB-T USB Stick (RTL2832U + E4000) with Antenna and Remote Control

SDR XTR Tiny SDR & DVB-T USB set, including quality telescopic antenna and remote control. Genuine E..

रo 4,290.00

bladeRF X40

bladeRF X40

Out of the box, the bladeRF can tune from 300MHz to 3.8GHz without the need for extra boards. Throug..

रo 66,033.00

bladeRF x115

bladeRF x115

Kit includes:   bladeRF x115 (115KLE Cyclone 4 FPGA) USB 3.0 SS cable 2x SMA..

रo 98,244.00

bladeRF x115 Thermal (-40C to 85C)

bladeRF x115 Thermal (-40C to 85C)

Kit includes:   bladeRF x115  (115KLE Cyclone 4 FPGA) USB 3.0 SS cable 2x SM..

रo 232,966.00

Nooelec NESDR SMArt v4 Bundle - Premium RTL-SDR with Aluminum Enclosure, 0.5PPM TCXO, SMA Input and 3 Antennas RTL2832U and R820T2-Based

Nooelec NESDR SMArt v4 Bundle - Premium RTL-SDR with Aluminum Enclosure, 0.5PPM TCXO, SMA Input and 3 Antennas RTL2832U and R820T2-Based

New version: SMArt v5 BundleNooelec NESDR SMArt v4 Bundle - Premium RTL-SDR w/ Aluminum Enclosure, 0..

रo 5,557.00

SMA Male to N Male Cable Connector

SMA Male to N Male Cable Connector

SMA Male to N Male Cable Connector   Characteristics:   1 ..

रo 375.00

SMA Male to CRC9 Male Cable Connector

SMA Male to CRC9 Male Cable Connector

SMA Male to CRC9 Male Cable Connector for 3G USB Modem   Length : Appx 20cm  ..

रo 160.00

SMA Male to MS156 Right Angled Male Cable Connector

SMA Male to MS156 Right Angled Male Cable Connector

SMA Male to MS156 Right Angled Male Cable Connector   Length : Appx 15cm Note: Product i..

रo 450.00

NooElec NESDR Mini 2+0.5PPM TCXO USB RTL-SDR Receiver (RTL2832 + R820T2) with Antenna

NooElec NESDR Mini 2+0.5PPM TCXO USB RTL-SDR Receiver (RTL2832 + R820T2) with Antenna

This custom Nooelec SDR is a modified DVB-T USB dongle tuned for SDR usage, including a high-accurac..

रo 4,545.00

SDR 1 MHz to 6 GHz - HackRf One

SDR 1 MHz to 6 GHz - HackRf One

SDR-1 MHz to 6 GHz   1 MHz to 6 GHz operating frequency half-duplex transceiver ..

रo 21,785.00

YARD Stick One

YARD Stick One

YARD Stick One (Yet Another Radio Dongle) can transmit or receive digital wireless signals at freque..

रo 8,927.00

Hak5 Elite Field Kit

Hak5 Elite Field Kit

This exclusive Field Kit combines the most popular Hak5 signature gear, all compiled in our Elite Eq..

रo 87,125.00

Balun One Nine - Tiny Low-Cost 1:9 HF Antenna Balun

Balun One Nine - Tiny Low-Cost 1:9 HF Antenna Balun

Meet 'Balun One Nine', a small, cost-effective balun. An excellent way to attach a long wire antenna..

रo 1,890.00

Male SMA to Male SMA pigtail cable, RG-316, 0.5' length

Male SMA to Male SMA pigtail cable, RG-316, 0.5' length

Very high-quality male SMA to male SMA RG-316 pigtail cable, 0.5' in length.Low-loss RG-316 and a sh..

रo 1,005.00

SDR Tiny RTL-USB Set with 0.5PPM TCXO, SMA Input, Aluminum Enclosure and Custom Heatsink NESDR Nano 3

SDR Tiny RTL-USB Set with 0.5PPM TCXO, SMA Input, Aluminum Enclosure and Custom Heatsink NESDR Nano 3

Say goodbye to blocked USB ports! The tiny NESDR Nano 3 is the ideal SDR for portable and embedded a..

रo 4,420.00

Nooelec 100661 SDR Al - 0.5PPM TCXO USB RTL-SDR Receiver (RTL2832 + R820T2) w/ Antenna and Remote Control, Installed in Aluminum Enclosure NESDR Mini 2+

Nooelec 100661 SDR Al - 0.5PPM TCXO USB RTL-SDR Receiver (RTL2832 + R820T2) w/ Antenna and Remote Control, Installed in Aluminum Enclosure NESDR Mini 2+

This is an ultra-high-accuracy RTL-SDR with an R820T2 tuner IC, pre-installed into a high quality bl..

रo 4,925.00

Nooelec RaTLSnake M6 v2 - Premium 3-Antenna Bundle for SMA-Input SDRs

Nooelec RaTLSnake M6 v2 - Premium 3-Antenna Bundle for SMA-Input SDRs

The first premium RTL-SDR antenna bundle! Perfect for all SMA-input SDRs like our NESDR SMArt series..

रo 2,900.00

NooElec HF Bundle: NESDR Smart

NooElec HF Bundle: NESDR Smart

NooElec NESDR Smart HF Bundle: 100kHz-1.7GHz Software Defined Radio Set for HF/UHF/VHF Including RTL..

रo 10,740.00

moRFeus: a field-configurable wideband frequency converter and signal generator

moRFeus: a field-configurable wideband frequency converter and signal generator

MoRFeus is a 30 MHz–6 GHz field-configurable Fractional-N wideband frequency converter and signal ge..

रo 20,741.00

HF Bundle: NESDR Mini 2+

HF Bundle: NESDR Mini 2+

This HF bundle contains everything you need to get you listening to HF radio on your computer, fast!..

रo 8,215.00

Ham It Up - 125MHz 0.5PPM TCXO Upgrade Module for Ham It Up v1.2+

Ham It Up - 125MHz 0.5PPM TCXO Upgrade Module for Ham It Up v1.2+

The TCXO is a custom 0.5PPM part made for us by our crystal partner in Taiwan. It has fantastic shor..

रo 1,255.00

HF Bundle: NESDR Mini

HF Bundle: NESDR Mini

This HF Bundle: NESDR Mini contains everything you need to get you listening to HF radio on your com..

रo 7,835.00

HF Bundle: NESDR XTR+

HF Bundle: NESDR XTR+

This HF Bundle: NESDR XTR+ contains everything you need to get you listening to HF radio on your com..

रo 9,605.00

Ham It Up - Aluminum Enclosure Kit for Ham It Up v1.3+

Ham It Up - Aluminum Enclosure Kit for Ham It Up v1.3+

These high-quality Ham It Up - Aluminum Enclosure Kit for Ham It Up v1.3+ are custom-made for all cu..

रo 2,015.00

HF Bundle: NESDR Mini 2

HF Bundle: NESDR Mini 2

This HF Bundle: NESDR Mini 2 contains everything you need to get you listening to HF radio on your c..

रo 7,960.00

Nooelec Ham It Down 3GHz Downconverter - Extends The Frequency of Your RTL-SDR

Nooelec Ham It Down 3GHz Downconverter - Extends The Frequency of Your RTL-SDR

Experience enhanced performance and versatility with the Ham It Down 3GHz Downconverter. Designed to..

रo 11,283.00

RF Explorer Upconverter

RF Explorer Upconverter

RF Explorer Upconverter is a high-performance RF frequency mixer to enable input frequency ranges fr..

रo 10,069.00

Adafruit 5100 MACROPAD RP2040 Bare Bones - 3x4 Keys + Encoder + OLED

Adafruit 5100 MACROPAD RP2040 Bare Bones - 3x4 Keys + Encoder + OLED

Strap yourself in, we're launching in T-minus 10 seconds...Destination? A new Class M planet called ..

रo 3,772.00

Nooelec NESDR SMArt v5 SDR - HF/VHF/UHF (100kHz-1.75GHz) RTL-SDR. RTL2832U & R820T2-Based Software Defined Radio

Nooelec NESDR SMArt v5 SDR - HF/VHF/UHF (100kHz-1.75GHz) RTL-SDR. RTL2832U & R820T2-Based Software Defined Radio

This premium RTL-SDR was designed, developed and fabricated by Nooelec in the USA and Canada. It all..

रo 4,290.00

Ham It Up Plus v2 - Extend the Range of Your RTL-SDR, NESDR

Ham It Up Plus v2 - Extend the Range of Your RTL-SDR, NESDR

Get ready to revolutionize your radio experience with the Ham It Up Plus v2--an addon for your RTL-S..

रo 8,845.00

Tags: Ham It Up, v1.3, RF, Upconverter, Software, Defined, Radio

The product is currently Out-of-Stock. Enter your email address below and we will notify you as soon as the product is available.

Name
Email
Phone
Comments