Gravity: Digital Signal Isolator is capable of isolating I2C digital signal and providing isolated power to the sensor module, effectively preventing mutual interference between the sensor modules. This digital signal isolator can be used for multi-parameter water quality detection systems to prevent water quality sensors from interfering with each other.
 
In many cases, interference sources are existing. For example, a running pump in a fish tank will release signals into the water, which interferes the sensors in the fish tank. In this case, electrical isolation is needed to ensure the stable operation of the sensors. Some sensors, such as pH sensors and electrical conductivity sensors, which share the same power source and measure in the same container, will interfere with each other and do not work properly. In order to ensure stable operation of the sensor modules, it is necessary to isolate the signal and the power.
 
After the analog signal isolator, we launched this digital signal isolator which specifically isolates the I2C digital signal. What's more, the on-board 5V isolation power chip can directly supply the sensor module, without additional power. This product is designed specifically for DFRobot I2C connector sensor or modules, plug and play, no welding. Connect it into your circuit to get electrical isolation, and the code of sensor module in control board does not need to be modified, which is simple and convenient.
 
 
Note:
1. Please pay attention to the operating current of your sensor or module, the maximum output current from Module side is 150mA.
2. All pins on the Module side (isolation side) are isolated from all pins on the Controller side (non-isolation side). Do not short-circuit them.
3. It is normal for the isolator generates heat while working.
 
Features: 
  • Onboard 5V 0.75W isolation power chip, no additional power needed, simple and convenient
  • Almost compatible with all DFRobot I2C connector sensors or modules, plug and play, no welding
Specifications
  • Operating Voltage: 5.0V
  • Connector Type: PH2.0-4P
  • Interface Protocol: I2C(IIC)
  • Interface Signal Level: High 3.3V, Low 0V
  • Dimension: 42 x 32mm / 1.65 x 1.26 inch
Controller Side (Non-isolation Side)
  • Supply Voltage: 5.0 ± 0.15V
  • No-load Current: 15mA(TYP)
Module Side(Isolation Side)
  • Output Voltage: 5.0 ± 0.15V
  • Output Current: 150mA(MAX)
Documents
Package Includes: 
  • 1 x Gravity: Digital I2C Signal Isolator
  • 1 x Double PH2.0-4P Cable               
  • 1 x Gravity-4P I2C/ UART Sensor Cable 
  • 2 x XH2.54-4Pin Header 

Write a review

Please login or register to review

Gravity: Digital I2C Signal Isolator

  • Brand: DFRobot
  • Product Code:DFR-Gravity-I2C-Signal-Isolator
  • Reward Points:16
  • Availability:In Stock
  • रo 1,584.00
  • रo 1,375.00

  • Price in reward points:1637

  • 10 or more रo 1,578.00
  • 15 or more रo 1,571.00
  • 45 or more रo 1,530.00

Related Products

Gravity: Analog Signal Isolator

Gravity: Analog Signal Isolator

In many cases, electrical isolation is required to ensure reliable operation of the sensors. Some se..

रo 1,665.00 रo 1,978.00

Adafruit 4903 ISO1540 Bidirectional I2C Isolator - STEMMA QT / Qwiic

Adafruit 4903 ISO1540 Bidirectional I2C Isolator - STEMMA QT / Qwiic

Whatever it is, you can use the Adafruit ISO1540 Bidirectional I2C Isolator to add full electrical i..

रo 856.00 रo 966.00

Gravity: I2C ADS1115 16-Bit ADC Module (Arduino & Raspberry Pi Compatible)

Gravity: I2C ADS1115 16-Bit ADC Module (Arduino & Raspberry Pi Compatible)

DFRobot I2C ADS1115 16-bit ADC module can accurately collect and convert analog signals. Through thi..

रo 1,435.00 रo 1,655.00

Tags: Gravity, I2C, Isolator

The product is currently Out-of-Stock. Enter your email address below and we will notify you as soon as the product is available.

Name
Email
Phone
Comments