STM32H743IIT6 development board

Overview:

  • OpenH743I-C is an STM32 development board designed for the STM32H743IIT6 microcontroller, consists of the mother board and the MCU core board CoreH743I.
  • The OpenH743I-C supports further expansion with various optional accessory boards for specific application. The modular and open design makes it the ideal for starting application development with STM32 series microcontrollers.

What's on the mother board:

STM32H743IIT6 development board on board resource

  1. MCU core board connector: for easily connecting the CoreH743I
  2. Arduino interface: for connecting Arduino shields
  3. DCMI interface: for connecting camera
  4. 8-bit FMC interface: easily connects to peripherals such as NandFlash
  5. ULPI interface: for connecting high-speed USB peripheral (the STM32H743I integrates USB HS controller without any PHY device)
  6. LCD interface 1: for connecting 10.1inch LCD, 7inch LCD, 4.3inch LCD
  7. LCD interface 2: for connecting 4.3inch LCD
  8. SAI1 interface: for connecting audio modules
  9. ICSP interface: Arduino ICSP
  10. SPI interfaces:
    1. easily connects to SPI peripherals such as DataFlash (AT45DBxx, W25QXX), SD card, MP3 module, etc.
    2. easily connects to AD/DA modules (SPI1 features AD/DA alternative function)
  11. Ethernet interface: for connecting Ethernet modules
  12. I2S / I2C interface: easily connects to I2S peripherals such as audio module, etc.
  13. USART1 connector: USB to UASRT via the onboard convertor CP2102 
  14. QUADSPI interface: 4-wires SPI interface (the H7 series latest peripheral interface), for connecting serial Flash modules like W25QXX Board
  15. SDMMC interface: for connecting Micro SD module, features much faster access speed rather than SPI
  16. USART3 interface: easily connects to RS232, RS485, USB TO 232, etc.
  17. CAN2 interface: for connecting CAN modules
  18. CAN1 interface: for connecting CAN modules
  19. I2C1/I2C4 interface: easily connects to I2C peripherals such as I/O expander (PCF8574), EEPROM (AT24Cxx), 10 DOF IMU Sensor, etc.
  20. MCU pins connector: all the MCU I/O ports are accessible on expansion connectors for further expansion
  21. 5V DC jack
  22. 5V/3.3V power input/output: usually used as power output, also common-grounding with other user board
  23. Power supply switch: powered from 5VDC OR USB connection of the USART1
  24. CP2102: USB to UART convertor
  25. LEDs: convenient for indicating I/O status and/or program running state
  26. Joystick: five positions
  27. WAKE UP button: used as regular button, and/or wake up the STM32 MCU from sleep
  28. Reset button
  29. USART1 jumper
  30. LED jumper:
    1. short the jumper to connect to default I/Os used in example code
    2. open the jumper to connect to custom I/Os via jumper wires
  31. KEY jumper:
    1. short the jumper to connect to default I/Os used in example code
    2. open the jumper to connect to custom I/Os via jumper wires
  32. Arduino jumper:
    • short the upper pins, A4, A5 is used as AD function

short the lower pins, A4, A5 is used as I2C function

What's on the CoreH743I:

STM32H743IIT6 development board on board resource

  • STM32H743IIT6:the high performance STM32 MCU which features:
    •  Core: Cortex-M7 32-bit RISC + double-precision FPU + Chrom-ART graphic accelerator
    • Feature: single-cycle DSP instructions
    • Operating Frequency: 480MHz, 1027 DMIPS / 2.14 DMIPS/MHz
    • Operating Voltage: 1.62V-3.6V
    • Package: LQFP176
    • Memories: 2MB Flash, 1MB RAM (864KB User+192KB TCM+4KB Backup)
    • MCU communication Interfaces:
      • 6 x SPI, 4 x USART, 4 x UART, 1 x LPUART, 3 x I2S
      • 4 x I2C, 2 x FDCAN, 1 x QUAD-SPI, 1 x DCMI, 4 x SAI
      • 1 x FMC, 2 x SDMMC, 10 x TIM , 5 x LPTIM
      • 1 x LTDC, 1 x SPDIFRX, 1 x HDMI-CEC, 1 x SWPMI
      • 2 x COMP, 2 x OPAMP, 1 x HRTIM, 1 x RNG, 1 x DM2D, 1 x MDIO, 1 x SysTick
      • 1 x USB 2.0 OTG FS
      • 1 x USB 2.0 OTG HS (supports external HS PHY through ULPI)
      • 1 x 10/100 Ethernet MAC
    • AD & DA converters: 3 x AD (16-bit); 2 x DA (12-bit)
    • Debugging/Programming: supports JTAG/SWD interfaces, supports IAP
    • IC42S16400J / IS42S16400J: SDRAM 1 Meg Bits x 16 Bits x 4 Banks (64-MBIT)
    • STMPS2151STR: onboard USB power management device
    • AMS1117-3.3: 3.3V voltage regulator
    • 8M crystal
    • 32.768K crystal, for internal RTC with calibration
    • Reset button
    • VBUS LED: USB port indicator
    • PWR LED: Power indicator
    • Power supply switch, powered from 5Vin or USB connection
    • Boot mode selection, for configuring BOOT0 pin
    • JTAG/SWD interface: for debugging/programming
    • USB connector, supports Device and/or Host
    • MCU pins expander, VCC, GND and all the I/O pins are accessible on expansion connectors for further expansion
  • POWER jumper:
    • VBAT: short the jumper to use system power supply, open it to connect external power, such as battery
    • VREF: short the jumper to connect VREF+ to VCC, open it to connect VREF+ to other custom pin via jumper wire
  • OTG jumper:
    • short the jumper when using USB OTG/HOST
    • open the jumper to disconnect from related I/O port

JTAG/SWD interfaces:

The figure 1, and 2 show the header pinouts of JTAG/SWD interface

JTAG Header Pinout SWD Header Pinout

Dimensions:

STM32 development board dimensions

Documentation:

  • Wiki
  • Schematic
  • Demo code (examples in C, FreeRTOS, μC/OS-III)
  • STM32 development software (KEIL, STM32CubeMX, etc.)
  • STM32 datasheets
  • STM32 development documentations

Package Includes:

  • 1 x OpenH743I-C development board
  • 1 x USB type A plug to micro B plug cable
  • 1 x USB type A receptacle to micro B plug cable
  • 1 x 4-pin 2-pin wires pack
  • 1 x 5V power adapter


Write a review

Please login or register to review

Waveshare 16884 OpenH743I-C Standard, STM32H7 Development Board

  • Brand: Waveshare Electronics
  • Product Code:NR-WaveS-openH743I-C-Standard-STM32H7
  • Reward Points:84
  • Availability:In Stock
  • रo 8,440.00
  • रo 7,090.00

  • Price in reward points:8440

  • 2 or more रo 8,375.00
  • 4 or more रo 8,305.00
  • 9 or more रo 8,238.00
  • 18 or more रo 8,170.00

Related Products

Waveshare 15238 EVK407I, STM32F4 Development Board

Waveshare 15238 EVK407I, STM32F4 Development Board

STM32 Development Board, STM32F407IGT6, USB HS/FS, Ethernet, NandFlash, JTAG/SWD, LCD, USB TO UARTOv..

रo 9,017.00 रo 10,735.00

Waveshare 16635 CoreH743I, STM32 STM32H743IIT6 MCU core board

Waveshare 16635 CoreH743I, STM32 STM32H743IIT6 MCU core board

STM32 STM32H743IIT6 MCU Core Board, Full IO Expander, JTAG/SWD Debug InterfaceOverview:CoreH743I is ..

रo 5,045.00 रo 6,005.00

CANBed - Arduino CAN-Bus RP2040 development board

CANBed - Arduino CAN-Bus RP2040 development board

CANBed RP2040 is a CAN Bus development board equipped with an RP2040 chip with a high-performance MC..

रo 1,853.00

ART-Pi STM32H750 Cortex-M7 Development Board

ART-Pi STM32H750 Cortex-M7 Development Board

The ART-Pi from RT-Thread Team is a DIY open source hardware with extended functions specially desig..

रo 8,248.00 रo 9,505.00

Waveshare 19188 / 19186ESP32 One, mini Development Board with WiFi / Bluetooth, Optional Camera

Waveshare 19188 / 19186ESP32 One, mini Development Board with WiFi / Bluetooth, Optional Camera

ESP32 One, Mini Development Board With WiFi / Bluetooth, Optional CameraESP32 ONE WIFI / BLUETOOTHIm..

रo 1,082.00 रo 1,290.00

Tags: Waveshare, Development, Board

The product is currently Out-of-Stock. Enter your email address below and we will notify you as soon as the product is available.

Name
Email
Phone
Comments