This sensor is a carrier/breakout board for the ST L3GD20 three-axis gyroscope, which measures the angular rates of rotation about the roll (X), pitch (Y), and yaw (Z) axes. Angular velocity measurements with a configurable range of ±250°/s, ±500°/s, or ±2000°/s can be read through a digital I²C or SPI interface. The board has a 3.3 V linear regulator and integrated level-shifters that allow it to work over an input voltage range of 2.5–5.5 V, and the 0.1″ pin spacing makes it easy to use with standard solderless breadboards and 0.1″ perfboards.
 
This board is a compact (0.5″ × 0.9″) breakout board for ST’s L3GD20 three-axis digital-output gyroscope; we therefore recommend careful reading of the L3GD20 datasheet (2MB pdf) before using this product. The L3GD20 is a great IC, but its small, leadless, LGA package makes it difficult for the typical student or hobbyist to use. It also operates at voltages below 3.6 V, which can make interfacing difficult for microcontrollers operating at 5 V. This carrier board addresses these issues by incorporating additional electronics, including a 3.3 V voltage regulator and level-shifting circuits, while keeping the overall size as compact as possible. The board ships fully populated with its SMD components, including the L3GD20, as shown in the product picture.
 
Compared to the older L3G4200D, the L3GD20 uses a higher resonant frequency that makes it more resistant to audio noise and vibrations. This board remains pin-compatible with the original L3G4200D carrier, although changes in I²C addresses and configuration registers mean that code written to interface with an L3G4200D might need to be modified to work with an L3GD20.
 
The L3GD20 has many configurable options, including three selectable angular rate sensitivities, a choice of output data rates, an embedded FIFO for buffering output data, and a programmable external interrupt signal. The three angular velocity readings are available through a digital interface, which can be configured to operate in either I²C or SPI mode.
 
The carrier board includes a low-dropout linear voltage regulator that provides the 3.3 V required by the L3GD20, which allows the sensor to be powered from a 2.5-5.5 V supply. The regulator output is available on the VDD pin and can supply almost 150 mA to external devices. The breakout board also includes a circuit that shifts the I²C/SPI clock and data in lines to the same logic voltage level as the supplied VIN, making it simple to interface the board with 5 V systems, and the board’s 0.1″ pin spacing makes it easy to use with standard solderless breadboards and 0.1″ perfboards.
 
For sensor fusion applications, our MinIMU-9 v3 and AltIMU-10 v4 inertial measurement units combine the similar L3GD20H with an LSM303D 3-axis accelerometer and 3-axis magnetometer on a single board, providing nine independent readings that can be used to calculate an absolute orientation. The AltIMU-10 v4 also includes an LPS25H pressure sensor that can be used to calculate altitude.
 
Specific​ations:
  • Dimensions: 0.5″ × 0.9″ × 0.1″ (13 × 23 × 3 mm)
  • Weight without header pins: 0.7 g (0.03 oz)
  • Operating voltage: 2.5 to 5.5 V
  • Supply current: 7 mA
  • Output format (I²C/SPI): one 16-bit reading per axis
  • Sensitivity range (configurable): ±250°/s, ±500°/s, or ±2000°/s
 
Included components:
  • A 9×1 strip of 0.1″ header pins and a 9×1 strip of 0.1″ right-angle header pins are included, as shown in the picture below. You can solder the header strip of your choice to the board for use with custom cables or solderless breadboards, or you can solder wires directly to the board itself for more compact installations.
 
Using the L3GD20 Connections
Regardless of the interface being used to communicate with the L3GD20, its VIN pin should be connected to a 2.5-5.5 V source, and GND should be connected to 0 volts. (Alternatively, if you are using the gyro with a 3.3 V system, you can leave VIN disconnected and bypass the built-in regulator by connecting 3.3 V directly to VDD.)
 
A minimum of two logic connections are necessary to use the L3GD20 in I²C mode (this is the default mode): SCL and SDA. These pins are connected to built-in level-shifters that make them safe to use at voltages over 3.3 V; they should be connected to an I²C bus operating at the same logic level as VIN. The remaining pins are not connected to level-shifters on the board and are not 5V-tolerant, but our 4-channel bidirectional logic level shifter can be used externally with those pins to achieve the same effect.
 
To use the L3GD20 in the default SPI mode, four logic connections are required: SPC, SDI, SDO, and CS. These should be connected to an SPI bus operating at the same logic level as VIN. The SPI interface operates in 4-wire mode by default, with SDI and SDO on separate pins, but it can be configured to use 3-wire mode so that SDO shares a pin with SDI.
 

Schematic Diagram

The above schematic shows the additional components the carrier board incorporates to make the L3GD20 easier to use, including the voltage regulator that allows the board to be powered from a 2.5-5.5 V supply and the level-shifter circuit that allows for I²C and SPI communication at the same logic voltage level as VIN.

 

Electrical Specifications
Minimum Operating Voltage 2.5V
Maximum Operating Voltage 5.5V
Physical Attributes
Weight 0.7g
Dimensions 0.5″ × 0.9″ × 0.1″
Additional Information
Warranty

Write a review

Please login or register to review

Pololu 2125 L3GD20 3-Axis Gyro Carrier with Voltage Regulator

  • Brand: Pololu
  • Product Code:Pololu-3-Axis-Gyro-Carrier
  • Reward Points:10
  • Availability:In Stock
  • रo 989.00

  • Price in reward points:989

  • 10 or more रo 891.00
  • 15 or more रo 884.00
  • 32 or more रo 877.00
  • 50 or more रo 779.00
  • 90 or more रo 772.00
  • 180 or more रo 766.00

Related Products

3 Axis Gyroscope + Accelerometer Module - GY-521 MPU6050

3 Axis Gyroscope + Accelerometer Module - GY-521 MPU6050

GY-521 6DOF MPU6050 Module 3 Axis Gyroscope + Accelerometer for MWC Arduino   Features:..

रo 90.00 रo 270.00

Me 3-Axis Accelerometer and Gyro Sensor

Me 3-Axis Accelerometer and Gyro Sensor

Me 3-Axis Accelerometer and Gyro Sensor is a motion processing module. It can use to measure the ang..

रo 2,370.00

9-Axis Gyro + Accelerator + Magnetometer Sensor Module MPU-9250

9-Axis Gyro + Accelerator + Magnetometer Sensor Module MPU-9250

9-Axis Gyro + Accelerator + Magnetometer Sensor Module MPU-9250   Features and Specification..

रo 420.00 रo 540.00

Pololu 2129 L3GD20H 3-Axis Gyro Carrier with Voltage Regulator

Pololu 2129 L3GD20H 3-Axis Gyro Carrier with Voltage Regulator

This board is a compact (0.4″ × 0.9″) breakout board for ST’s L3GD20H three-axis digital-output gyro..

रo 669.00

9-Axis Gyro + Accelerator + Magnetometer Sensor Module/ Kit MPU-9150

9-Axis Gyro + Accelerator + Magnetometer Sensor Module/ Kit MPU-9150

The MPU-9150 is the world's first 9-axis MotionTracking device designed for the low power, low cost,..

रo 1,060.00 रo 1,390.00

9-Axis Gyro + Accelerator + Magnetometer Sensor Module MPU-9255

9-Axis Gyro + Accelerator + Magnetometer Sensor Module MPU-9255

9-Axis Gyro + Accelerator + Magnetometer Sensor Module MPU-9255   Features and Specific..

रo 1,047.00

Pololu 2739/2469/2470 AltIMU-10 Gyro, Accelerometer, Compass, and Altimeter (L3GD20H, LSM303D and LPS331AP/ LPS25H Carrier)

Pololu 2739/2469/2470 AltIMU-10 Gyro, Accelerometer, Compass, and Altimeter (L3GD20H, LSM303D and LPS331AP/ LPS25H Carrier)

The Pololu AltIMU-10 v3/v4 is an inertial measurement unit (IMU) and altimeter that features the sam..

रo 3,730.00

Tags: Pololu, 2125, L3GD20, 3-Axis, Gyro, Carrier, Voltage, Regulator

The product is currently Out-of-Stock. Enter your email address below and we will notify you as soon as the product is available.

Name
Email
Phone
Comments