Consists of ODROID-HC4 board, a case made of a rigid PCB that can mount two 3.5-inch HDDs horizontally, cooling fan, cables and bolts. It’s your own network storage device that you can enjoy creating yourself, and the HC4’s Petitboot function and various latest OS support can be used without any changes. Please note that this product cannot mount any 2.5-inch storage device.

Note! This KIT does NOT include OLED+RTC for HC4-P.  (Sold individually)


Board Detail:


  • CPU (Amlogic S905X3):
    • B DDR4 memory (4GiB)
    • C 2x SATA ports
    • D 1x RJ45 Ethernet port (10/100/1000)
    • E 1x HDMI 2.0
    • F 1x USB 2.0 host port
    • G 1x DC power jack (Outer diameter : 5.5mm, inner diameter 2.1mm)
    • H 2x System LED indicators
    • I 1x UART for system console
    • J 1x IR receiver
    • K 5x GPIO pins (for optional OLED display)
    • L 1x Micro SD slot
    • M 1x Cooling fan
    • N 1x Boot switch

Block diagram:


SATA interface performance:

  • We connected a SATA SSD to the HC4 platform and measured the storage IO throughput. We could observe 390~420MB/s transfer speed which is not saturated at the maximum level ~500MB/s which is quite good for many applications.

SMB/CIFS network file transfer performance over the Gbit Ethernet connection

  • As shown below Windows OS client shows a sustainable 100+ MB/s transfer speed when we download/upload large files.

Downloading:


Uploading:


Helios LAN Test Result

  • Samsung 860 EVO 250GB SSD


Seagate Barracuda 2TB HDD (ST2000DM006)


Power Consumption

Note 1: ST2000DM006 spin-down power consumption is 0.75W per HDD. Therefore, the HC4 idle mode power consumption is about 4W.

Note 2: Power consumption in Active state is tested while copying huge files through SAMBA service.

Note 3: Wake-up sources for the Suspend mode: Wake-on-LAN, IR remote receiver and RTC Alarm.

Software Support

Petitboot can find the OS on the SD card, the HDD or the SSD. So even if you do not have an SD card but you have a plugged-in HDD or SSD that has an OS installed, Petitboot will boot the HC4 using the OS from the HDD or SSD. Debian/Ubuntu OS can run with the Hardkernel’s preinstalled OS image or Debian/Ubuntu Netboot Installer which you can obtain from the ODROID forum.

Supported Linux kernel versions are:

  • 4.9.230 or newer (Hardkernel stock OS version)
  • Mainline kernel 5.15 or newer (Unofficial version from ODROID forum)

Specifications

  • FORM FACTOR
    • Board Dimensions: 84mm x 90.5mm x 25.0mm
    • Transformation KIT Dimensions : 225mm x 106mm x 127mm
    • Weight: 615g including board and transformation KIT without HDD
  • PROCESSOR
    • Amlogic S905X3 Processor
    • L1 instruction cache: 32 KB, 4-way set associative (128 sets), 64 byte lines, shared by 1 processor
    • L1 data cache: 32 KB, 4-way set associative (128 sets), 64 byte lines, shared by 1 processor
    • L3 data cache: 512KB , 16-way set associative (512 sets), 64 byte lines, shared by 4 processorsQuad-Core Cortex-A55 (1.800GHz)
    • ARMv8-A architecture with Neon and Crypto extensions
    • Mali-G31 MP2 GPU with 4 x Execution Engines (650Mhz)
  • MEMORY
    • DDR4 4GiB with 32-bit bus width
    • Data rate: 2640 MT/s (PC4-21333 grade)
    • 1.2Volt low power design
  • STORAGE
    • 1x Micro SD slot (DS/HS mode up to UHS-I SDR104)
  • NETWORKING
    • 1 x GbE LAN ports (RJ45, supports 10/100/1000 Mbps)
    • – Realtek RTL8211F (Ethernet transceiver)
    • – LED indicators
    • * Green LED: Flashing by data traffics at 100Mbps connection
    • * Amber LED: Flashing by data traffics at 1000Mbps connection
  • VIDEO
    • 1 x HDMI 2.0 (up to 4K@60Hz with HDR, CEC, EDID)
  • AUDIO
    • 1 x HDMI digital output
  • COOLER
    • Passive heatsink ( 40x32x10 mm ) on the CPU of PCB board
    • Bearing : Hydraulic Bearing FAN
    • – Rated Voltage : 5V
    • – Rated Current : 0.2A
    • – Max Speed RPM : 2000RPM
    • – Air Flow CFM : 33
    • – Air Pressure (In H2O) : 0.08
    • – Noise Level(dBA) : 26.5
    • – Dimension : 92X92X25MM
    • – Wire & Connector : 150mm, 4pin 1.25mm pitch
  • EXTERNAL I/O
    • 1 x USB 2.0 host port
    • 1 x Debug serial console (UART)
    • 2 x SATA Connectors
  • OTHER FEATURES
    • IR receiver for remote controller
    • System LED Indicators:
    • – Red (POWER) – Solid light when DC power is connected
    • – Blue (ALIVE) – Flashing like heartbeat while Kernel is running.
  • POWER
    • 1 x DC jack : outer (negative) diameter 5.5mm, inner (positive) diameter 2.1mm
    • DC input : 14.5V ~ 15.5V
    • – DC 15V/4A power adaptor is recommended. Sold separately.
    • Power consumption with two ST2000DM006 HDDs :
    • – IDLE(with HDD in spin-down) : ≃ 5.88W
    • – Active(using SAMBA): ≃ 15.59W
    • – Suspend: ≃ 0.29W


Note: 

The supplier of the product has no replacement and/or refund policy as part of their product warranty/guarantee. Furthermore, the repair cost and the cost of shipping to and fro from South Korea has to be borne. As Fab.to.Lab is merely an intermediary we extend the exact same warranty terms to all customers of Harkernel.

Please find more details here: Supplier warranty terms and conditions: https://www.hardkernel.com/agreement/

Documentation:

Package Includes:

  • 1 x ODROID-HC4 board
  • 1 x case made of a rigid PCB that can mount two 3.5-inch HDDs horizontally
  • 1 x cooling fan
  • 1 x cables set
  • 1 x bolts set

Write a review

Please login or register to review

ODROID-HC4-P KIT

  • Brand: Hardkernel
  • Product Code:NR-Hdk-ODROID-HC4-P-KIT
  • Reward Points:116
  • Availability:In Stock
  • रo 11,572.00

  • Price in reward points:11572

  • 2 or more रo 11,476.00
  • 4 or more रo 11,428.00
  • 5 or more रo 11,380.00
  • 10 or more रo 11,285.00

Available Options


Related Products

Odroid-HC2 Case

Odroid-HC2 Case

                Str..

रo 657.00

Power Adapter 15V/4A

Power Adapter 15V/4A

For ODROID-H2, ODROID-H2plus, ODROID-H3, ODROID-H3plus, ODROID-HC4, ODROID-HC4-P, ODROID-M1AC 100~24..

रo 1,344.00

ODROID-HC4

ODROID-HC4

ODROID-HC4 is new Home-Cloud platform based on the same ARM CPU as the ODROID-C4. We adopted a 12nm ..

रo 9,599.00

OLED+RTC for HC4-P

OLED+RTC for HC4-P

Made with an OLED display and RTC chip, this module can be mounted on ODROID-HC4 and ODROID-HC4-P pr..

रo 1,315.00

Tags: ODROID, HC4, Kit

The product is currently Out-of-Stock. Enter your email address below and we will notify you as soon as the product is available.

Name
Email
Phone
Comments