What's life without a little RISC? This miniature dev board is perfect for small projects: it comes with our favorite connector - the STEMMA QT, a chainable I2C port, WiFi, Bluetooth LE, and plenty of FLASH and RAM memory for many IoT projects. What a cutie pie! Or is it... a QT Py? This diminutive dev board comes with a RISC-V IoT microcontroller, the ESP32-C3!
  • ESP32-C3 is a low-cost microcontroller from Espressif that supports 2.4 GHz Wi-Fi and Bluetooth® Low Energy (Bluetooth LE). It has built-in USB-to-Serial, but not native USB - it cannot act as a keyboard or disk drive. The chip used here has 4MB of Flash memory, 400 KB of SRAM and can easily handle TLS connections.
  • The ESP32-C3 integrates a rich set of peripherals, ranging from UART, I2C, I2S, remote control peripheral, LED PWM controller, general DMA controller, TWAI controller, USB Serial/JTAG controller, temperature sensor, and ADC. It also includes SPI, Dual SPI, and Quad SPI interfaces. There is no DAC or native capacitive touch.
  • There's a minimum number of pins on this chip, it's specifically designed to be low cost and for simpler projects than ESP32-Sx or ESP32 classics with their large number of GPIO. Think of it more as an intended replacement to the ESP8266 than to the ESP32!
  • With its state-of-the-art power and RF performance, this SoC is an ideal choice for a wide variety of application scenarios relating to the Internet of Things (IoT), wearable electronics, and smart homes.
  • Please note: The C3 uses RISC V as a core, not Tensilica, and has Bluetooth LE (not classic!). The BLE core supports BT version 5 including Mesh. CircuitPython support is basic and does not include BLE at this time.
OLEDs! Inertial Measurement Units! Sensors a-plenty. All plug-and-play thanks to the innovative chainable design: SparkFun Qwiic-compatible STEMMA QT connectors for the I2C bus so you don't even need to solder! Just plug in a compatible cable and attach it to your MCU of choice, and you’re ready to load up some software and measure some light. Seeed Grove I2C boards will also work with this adapter cable.
  • Pinout and shape are Seeed Xiao compatible, with castellated pads. In addition to the QT connector, we also added an RGB NeoPixel, a reset button (great for restarting your program or entering the ROM bootloader), and a button on GPIO 9 for entering the ROM bootloader or for user input
  • Same size, form-factor, and pin-out as Seeed Xiao
  • USB Type C connector - If you have only Micro B cables, this adapter will come in handy!
  • ESP32-C3 32­-bit RISC­-V single­ core processor with 4MB of Flash memory, 400 KB of SRAM
  • Built in USB-to-Serial inside the chip, which can also be used for JTAG programming. This peripheral is not native serial, so not for USB HID, MIDI or MSC: it does reduce cost since a separate converter isnt needed
  • Can be used with Arduino IDE or MicroPython
  • Built-in RGB NeoPixel LED note that due the small number of GPIO, we could not add a NeoPixel power pin
  • Battery input pads on underside with diode protection for external battery packs up to 6V input
13 GPIO pins:
    • 11 on breakout pads
    • 5 x 12-bit analog inputs on A0 thru A3 and SDA pin
    • PWM outputs on any pin
    • I2C port, on the breakout pads shared with the STEMMA QT plug-n-play connector
    • Hardware UART which is also the hardware serial debug port
    • Hardware SPI
    • Hardware I2S on any pins
  • 3.3V regulator with 600mA peak output
  • Light sleep at 500uA, deep sleep at ~300uA. Lower power deep-sleep is not possible because we don't have an extra GPIO for disabling the NeoPixel power and we didn't want to share that with any of the IO pads. An engineering trade-off!
  • Reset switch for starting your project code over, boot 9 button for entering bootloader mode
  • Really really small

Technical Details:
Revision History:
As of July 7, 2022 - This board may come with a different regulator than AP2112K due to parts shortages. The regulator can provide at least 500mA.
  • Product Dimensions: 22.0mm x 17.8mm x 5.7mm / 0.9" x 0.7" x 0.2"

Documentation:

Package Includes:
  • 1 x Adafruit 5405 QT Py ESP32-C3 WiFi Dev Board with STEMMA QT 

Write a review

Please login or register to review

Adafruit 5405 QT Py ESP32-C3 WiFi Dev Board with STEMMA QT

  • Brand: Adafruit
  • Product Code:NR-Ada-5405-QT-Py-ESP32-C3
  • Reward Points:11
  • Availability:Back-order
  • रo 1,075.00

  • Price in reward points:1135

  • 45 or more रo 940.00
  • 145 or more रo 936.00

Related Products

Adafruit 5303 ESP32-S2 Feather with BME280 Sensor - STEMMA QT - 4MB Flash + 2 MB PSRAM

Adafruit 5303 ESP32-S2 Feather with BME280 Sensor - STEMMA QT - 4MB Flash + 2 MB PSRAM

Adafruit ESP32-S2 Feather with BME280 temperature/humidity/pressure sensor built right in! With nati..

रo 2,693.00

Adafruit 5325 QT Py ESP32-S2 WiFi Dev Board with STEMMA QT

Adafruit 5325 QT Py ESP32-S2 WiFi Dev Board with STEMMA QT

What has your favorite Espressif WiFi microcontroller, comes with our favorite connector - the STEMM..

रo 1,349.00

Adafruit 5348 QT Py ESP32-S2 WiFi Dev Board with uFL Antenna Port-STEMMA QT-  Coming Soon

Adafruit 5348 QT Py ESP32-S2 WiFi Dev Board with uFL Antenna Port-STEMMA QT- Coming Soon

What has your favorite Espressif WiFi microcontroller, comes with our favorite connector - the STEMM..

रo 1,349.00

Adafruit 5700 QT Py S3 with 2MB PSRAM WiFi Dev Board with STEMMA QT

Adafruit 5700 QT Py S3 with 2MB PSRAM WiFi Dev Board with STEMMA QT

The ESP32-S3 has arrived in QT Py format - and what a great way to get started with this powerful ne..

रo 1,350.00

Adafruit 5397 LiIon or LiPoly Charger BFF Add-On for QT Py

Adafruit 5397 LiIon or LiPoly Charger BFF Add-On for QT Py

Is your QT Py all alone, lacking a friend to travel the wide world with? When you were a kid you may..

रo 534.00

Adafruit 5787 ESP32-C3-DevKit-RUST-1 - 4 MB Flash

Adafruit 5787 ESP32-C3-DevKit-RUST-1 - 4 MB Flash

ESP32-C3-DevKit-RUST-1 is an entry-level RISC V development board equipped with the ESP32-C3-MINI-1,..

रo 2,690.00

Adafruit 5395 QT Py ESP32 Pico - WiFi Dev Board with STEMMA QT - 8MB Flash 2MB PSRAM

Adafruit 5395 QT Py ESP32 Pico - WiFi Dev Board with STEMMA QT - 8MB Flash 2MB PSRAM

This dev board is like when you're watching a super-hero movie and the protagonist shows up in a tot..

रo 1,615.00

Adafruit 5973 CH9328 UART to HID Keyboard Breakout

Adafruit 5973 CH9328 UART to HID Keyboard Breakout

We love using chips with 'native USB' peripherals - that's the magic silicon that lets a microcontro..

रo 750.00

Tags: Adafruit, ESP32, STEMMA QT, WiFi, Dev, Board

The product is currently Out-of-Stock. Enter your email address below and we will notify you as soon as the product is available.

Name
Email
Phone
Comments