The ESP32-S3-DevKitC-1 is an entry-level development board equipped with ESP32-S3-WROOM-1, a general-purpose Wi-Fi + Bluetooth LE MCU module that integrates complete Wi-Fi and Bluetooth LE functions. This version is equipped with the ESP32-S3-WROOM-1 (PCB antenna) with 8MB Flash and no PSRAM.

Please note: The S3 is similar  to the ESP32-S2 - but adds a dual core and Bluetooth LE (not classic!) However, there is minimal support for this dev board. For example, as of the time of this writing, there is no Arduino or CircuitPython support - only ESP IDF! Please purchase if you're doing development with the S3, and OK with stuff not working 100% out of the box.

Most of the I/O pins on the module are broken out to the pin headers on both sides of this board for easy interfacing. Developers can either connect peripherals with jumper wires or mount ESP32-S3-DevKitC-1 on a breadboard. We particularly like that there's a debug UART/USB port and a separate native USB port, so you can upload/debug/USB all at once.

At the core of the module is an ESP32-S3FN8, an Xtensa 32-bit LX7 CPU that operates at up to 240 MHz. You can power off the CPU and make use of the low-power co-processor to constantly monitor the peripherals for changes or crossing of thresholds.

ESP32-S3FN8 integrates a rich set of peripherals including SPI, LCD, Camera interface, UART, I2C, I2S, remote control, pulse counter, LED PWM, USB Serial/Jtag, MCPWM, SDIO host, GDMA, TWAI controller (compatible with ISO 11898-1, i.e. CAN Specification 2.0), ADC, touch sensor, temperature sensor, timers, and watchdogs, as well as up to 45 GPIOs. It also includes a full-speed USB 1.1 On-The-Go (OTG) interface to enable USB communication

There are three mutually exclusive ways to provide power to the board:

  • USB-to-UART Port and ESP32-S3 USB Port (either one or both), default power supply (recommended)
  • 5V and G (GND) pins
  • 3v3 and G (GND) pins

Components:

  • ESP32-S3-WROOM-1: ESP32-S3-WROOM-1 is a powerful, generic Wi-Fi + Bluetooth LE MCU module that has a rich set of peripherals. It provides acceleration for neural network computing and signal processing workloads. ESP32-S3-WROOM-1 comes with a PCB antenna.
  • 5V to 3.3V LDO: Power regulator that converts a 5V supply into a 3.3V output.
  • Pin Headers: All available GPIO pins (except for the SPI bus for flash) are broken out to the pin headers on the board for easy interfacing and programming. For details, please see Header Block.
  • USB-to-UART Port: A Micro-USB port used for power supply to the board, for flashing applications to the chip, as well as for communication with the chip via the on-board USB-to-UART bridge.
  • Native ESP32-S3 USB Port: ESP32-S3 full-speed USB OTG interface, compliant with the USB 1.1 specification. The interface is used for power supply to the board, for flashing applications to the chip, for communication with the chip using USB 1.1 protocols, as well as for JTAG debugging.
  • Boot Button: Download button. Holding down Boot and then pressing Reset initiates Firmware Download mode for downloading firmware through the serial port.
  • Reset Button
  • USB-to-UART Bridge: Single USB-to-UART bridge chip provides transfer rates up to 3 Mbps.
  • RGB LED: Addressable RGB LED, driven by GPIO48.
  • 3.3V Power On LED: Turns on when the USB power is connected to the board.

Documents:

Package Includes:

  • 1 x Adafruit 5312 ESP32-S3-DevKitC-1-N8 - ESP32-S3-WROOM-1 Dev Board - 8MB Flash

Write a review

Please login or register to review

Adafruit 5312 ESP32-S3-DevKitC-1-N8 - ESP32-S3-WROOM-1 Dev Board - 8MB Flash

  • Brand: Adafruit
  • Product Code:Ada-5312-ESP32-S3-DevKitC
  • Reward Points:22
  • Availability:In Stock
  • रo 2,152.00

  • Price in reward points:2270

  • 60 or more रo 2,143.00

Related Products

Adafruit 5715 ESP32-H2-DevKitM-1 - 4 MB Flash

Adafruit 5715 ESP32-H2-DevKitM-1 - 4 MB Flash

ESP32-H2-DevKitM-1 is an entry-level development board based on Bluetooth® Low Energy and IEEE 802.1..

रo 1,350.00

Adafruit 5337 ESP32-C3 RISC V Developer Board - 4 MB SPI Flash - DevKitC-02 ESP32-C3-WROOM-02

Adafruit 5337 ESP32-C3 RISC V Developer Board - 4 MB SPI Flash - DevKitC-02 ESP32-C3-WROOM-02

The ESP32-C3-DevKitC-02 is an entry-level RISC V development board equipped with the ESP32-C3-WROOM-..

रo 1,340.00

Adafruit 5310 ESP32-S3-DevKitC-1-N8R2 - ESP32-S3-WROOM-1 - 8MB Flash 2MB PSRAM

Adafruit 5310 ESP32-S3-DevKitC-1-N8R2 - ESP32-S3-WROOM-1 - 8MB Flash 2MB PSRAM

The ESP32-S3-DevKitC-1 is an entry-level development board equipped with ESP32-S3-WROOM-1, a general..

रo 2,361.00

Adafruit 5311 ESP32-S3-DevKitM-1-N8 - ESP32-S3-MINI-1 Dev Board - 8 MB Flash

Adafruit 5311 ESP32-S3-DevKitM-1-N8 - ESP32-S3-MINI-1 Dev Board - 8 MB Flash

The ESP32-S3-DevKitM-1 is an entry-level development board equipped with the ESP32-S3-MINI-1, a powe..

रo 2,152.00

Adafruit 5364 ESP32­-S3­-DevKitC-1-ESP32-S3-WROOM-2-32MB Flash 8MB PSRAM

Adafruit 5364 ESP32­-S3­-DevKitC-1-ESP32-S3-WROOM-2-32MB Flash 8MB PSRAM

The ESP32-S3-DevKitC-1 is an entry-level development board equipped with ESP32-S3-WROOM-2, a general..

रo 2,691.00

Adafruit 5483 ESP32-S3 TFT Feather - 4MB Flash, 2MB PSRAM, STEMMA QT

Adafruit 5483 ESP32-S3 TFT Feather - 4MB Flash, 2MB PSRAM, STEMMA QT

We've got a new machine here at Adafruit, it can uncover your deepest desires. Don't believe me? I'l..

रo 2,693.00

Adafruit 5835 Espressif ESP32-S3-BOX-3

Adafruit 5835 Espressif ESP32-S3-BOX-3

With its freely available development resources, ESP32-S3-BOX-3 is the ultimate choice for prototypi..

रo 6,739.00

Tags: ESP32, Development Board

The product is currently Out-of-Stock. Enter your email address below and we will notify you as soon as the product is available.

Name
Email
Phone
Comments